check engine MERCEDES-BENZ E550 4MATIC 2007 W211 Owner's Manual

Contents
At the gas station .............................. 321
Refueling ...................................... 321
Check regularly and before a
long trip........................................ 323
Engine compartment ......................... 325
Hood ............................................ 325
Engine oil ..................................... 327
Transmission fluid level ................ 329
Coolant level ................................ 330
Battery ......................................... 331
Windshield washer system and
headlamp cleaning system* ......... 332
Tires and wheels ................................ 333
Important guidelines .................... 333
Tire care and maintenance........... 334
Direction of rotation ..................... 336
Loading the vehicle ...................... 336
Recommended tire inflation
pressure ....................................... 341
Checking tire inflation pressure ... 342
Tire labeling.................................. 350
Load identification ....................... 354
DOT, Tire Identification Number
(TIN) ............................................. 355
Maximum tire load ....................... 356
Maximum tire inflation pressure .. 357Uniform Tire Quality Grading
Standards (U.S. vehicles) .............. 357
Tire ply material ............................ 359
Tire and loading terminology......... 359
Rotating tires ................................ 362
Winter driving ..................................... 364
Winter tires ................................... 364
Block heater* (Canada only) ......... 365
Snow chains.................................. 365
Maintenance....................................... 366
Maintenance service indicator
message ....................................... 366
Calling up the maintenance
service indicator display ............... 368
Resetting the maintenance
service indicator ........................... 368
Vehicle care........................................ 369
Cleaning and care of vehicle ......... 369
Practical hints.................................. 379
What to do if … ................................... 380
Lamps in instrument cluster ......... 380
Lamp in center console ................ 393
Vehicle status messages in the
multifunction display .................... 396
Where will I find ...? ............................ 432
First aid kit.................................... 432
Spare wheel .................................. 432
Luggage box ................................. 433
Vehicle tool kit.............................. 434
Vehicle jack .................................. 434
Unlocking/locking in an emergency .. 436
Unlocking the vehicle ................... 436
Locking the vehicle ....................... 437
Manually unlocking the gear
selector lever ................................ 438
Opening/closing in an emergency ..... 439
Power tilt/sliding sunroof or
panorama roof with power
tilt/sliding panel* ......................... 439
Resetting activated head restraints.... 440
Replacing SmartKey batteries ............ 441
SmartKey/SmartKey with
KEYLESS-GO* ............................... 441

23 At a glance
Exterior view
Item
Page
1
Trunk

Unlocking
120


Opening and closing
120,
122


Spare wheel
432


Vehicle tool kit
434
2
Rear lamps
445
3
Rear window, defrosting
203
4
Fuel filler flap
321
Gasoline
496
5
Doors

Locking and unlocking
110


Opening and closing
119
Item
Page
6
Towing eye bolt
468
General information
466
7
Rims and tires
481


Checking tire inflation
pressure
342


Spare wheel
432


Flat tire
452
8
Front lamps
444
9
Hood, opening
325
Engine oil
327
Coolant
330
Item
Page
a
Windshield wipers
58
Wiper blades, replacing
450
Wiper blades, cleaning
374
b
Window, cleaning
374
c
Roofs

Power tilt/sliding sun-
roof
242


Panorama roof with
power tilt/sliding panel*
245
d
Exterior rear view mirror
47
Parking position
136
e
Headlamp cleaning system*
198

38 Getting startedUnlockingSmartKeyStarter switch0For removing SmartKey
1Power supply for some electrical con-
sumers, such as seat adjustment2Ignition (power supply for all electrical
consumers) and driving position.
All lamps (except low beam headlamp
indicator lamp, high beam headlamp in-
dicator lamp, and turn signal indicator
lamps unless activated) in the instru-
ment cluster come on. If a lamp in the
instrument cluster fails to come on
when the ignition is switched on, have
it checked and replaced if necessary. If
a lamp in the instrument cluster re-
mains on after starting the engine or
comes on while driving, refer to “Lamps
in instrument cluster” (
page 380).
3Starting position
For information on starting the engine us-
ing the SmartKey, see “Starting with the
SmartKey” (
page 52).
i
When you switch on the ignition, the indica-
tor and warning lamps (except low beam head-
lamp indicator lamp, high beam headlamp
indicator lamp, and turn signal indicator lamps
unless activated) in the instrument cluster come
on. The indicator and warning lamps (except low
beam headlamp indicator lamp, high beam head-
lamp indicator lamp, and turn signal indicator
lamps if activated) should go out when the en-
gine is running. This indicates that the respective
systems are operational.
i
The SmartKey can only be removed from the
starter switch with the gear selector lever in
positionP.
i
If the SmartKey is left in starter switch
position0 for an extended period of time, it can
no longer be turned in the switch. In this case,
the steering is locked. To unlock, remove
SmartKey from the starter switch and reinsert.
!
If the SmartKey cannot be turned in the
starter switch, the battery may not be
sufficiently charged.


Check the battery and charge it if necessary
(page 462).


Get a jump start (
page 464).
To prevent accelerated battery discharge or a
completely discharged battery, always remove
the SmartKey from the starter switch when the
engine is not in operation.

40 Getting startedUnlockingIgnition (or position 2)
Press KEYLESS-GO start/stop button
twice.
This supplies power for all electrical
consumers. All lamps in the instrument
cluster (except low beam headlamp in-
dicator lamp, high beam headlamp indi-
cator lamp, and turn signal indicator
lamps unless activated) come on. If a
lamp in the instrument cluster fails to
come on when the ignition is switched
on, have it checked and replaced if nec-
essary. If a lamp in the instrument clus-
ter remains on after starting the engine
or comes on while driving, see “Lamps
in instrument cluster” (
page 380).For information on starting the engine us-
ing the KEYLESS-GO start/stop button,
see “Starting with KEYLESS-GO*”
(
page 53).
i
If you now press the KEYLESS-GO
start/stop button once, the power supply is
again switched off.
i
When you switch on the ignition, the indica-
tor and warning lamps (except low beam head-
lamp indicator lamp, high beam headlamp
indicator lamp, and turn signal indicator lamps
unless activated) in the instrument cluster come
on. The indicator and warning lamps (except low
beam headlamp indicator lamp, high beam head-
lamp indicator lamp, and turn signal indicator
lamps if activated) should go out when the en-
gine is running. This indicates that the respective
systems are operational.

58 Getting startedDrivingWindshield wipers
The combination switch is located on the
left of the steering column.Combination switch1Switching on windshield wipers
2Single wipe
Wiping with windshield washer fluid
Switch on the ignition (
page 37).Switching on/off windshield wipers

Turn the combination switch to the de-
sired position depending on the inten-
sity of the rain.
MWindshield wipers off
USlow intermittent wiping
Rain sensor operation with low
sensitivity.
VFast intermittent wiping
Rain sensor operation with high
sensitivity.
uSlow continuous wiping
tFast continuous wiping
!
Do not operate the windshield wipers when
the windshield is dry. Dust that accumulates on
a windshield might scratch the glass and/or
damage the wiper blades when wiping occurs on
a dry windshield. If it is necessary to operate the
windshield wipers in dry weather conditions, al-
ways operate the windshield wipers with wind-
shield washer fluid (
page 59).
!
If anything blocks the windshield wipers
(leaves, snow, etc.), switch them off immediate-
ly.


For safety reasons, stop the vehicle in a safe
location and

remove SmartKey from starter switch
or


turn off the engine by pressing the
KEYLESS-GO* start/stop button and
open the driver’s door (with the driver’s
door open, starter switch is in
position0, same as with SmartKey re-
moved from starter switch)
before attempting to remove any blockage.


Remove blockage.


Turn the windshield wipers on again.If windshield wipers fail to function at all in com-
bination switch positionU or V,


set the combination switch to the next high-
er wiper speed


have the windshield wipers checked at the
nearest authorized Mercedes-Benz Center.
i
When the windshield wipers are switched on
and you brake the vehicle to a stop, the time in-
terval between wiper operations is increased.

60 Getting startedDrivingProblems while driving
The engine runs erratically and misfires

An ignition cable may be damaged
(gasoline engine only).


The engine electronics may not be op-
erating properly.


Unburned gasoline may have entered
the catalytic converter and damaged it
(gasoline engine only).

Give very little gas.

Have the problem repaired by an
authorized Mercedes-Benz Center as
soon as possible.The coolant temperature is above
248°F (120°C)
The coolant is too hot and is no longer
cooling the engine.

Stop the vehicle as soon as possible in
a safe location and turn off the engine.
Allow engine and coolant to cool off.

Check the coolant level and add cool-
ant if necessary (
page 330).In case of accident
If the vehicle is leaking fuel:

Do not start the engine under any cir-
cumstances.

Notify local fire and/or police authori-
ties.
If the extent of the damage cannot be de-
termined:

Notify an authorized Mercedes-Benz
Center.
If no damage can be determined on the


major assemblies


fuel system


engine mount:

Start the engine in the usual manner.

76 Safety and SecurityOccupant safetyFurthermore, the occupant weight may ap-
pear to increase or decrease due to
objects hanging on the seat, other passen-
gers pushing on the seat, objects lodged
underneath the seat or stuffed between
seat and middle console or between seat
and door or due to objects applying pres-
sure on the back of the seat. Always make
sure that the seat has clearance in all di-
rections at all times.
Both driver and the front passenger should
always use the 75 indicator
lamp as an indication of whether or not the
front passenger is properly positioned.i
If your seat, including your trim cover and
cushion needs to be serviced in any way, take
the vehicle to your authorized Mercedes-Benz
Center.
Only seat accessories approved by
Mercedes-Benz may be used.
Warning!
G
If the 75 indicator lamp illumi-
nates when an adult or someone larger than
a small individual is in the front passenger
seat, have the front passenger re-position
himself or herself in the seat until the
75 indicator lamp goes out, or
check whether objects are caught under or
around the seat.
More information about air bag display mes-
sages (
page 403).
In the event of a collision, the air bag control
unit will not allow front passenger front
air bag deployment when the OCS classified
the front passenger seat occupant as being
up to or less than the weight of a typical
12-month-old child in a standard child re-
straint or if the front passenger seat is
sensed as being empty.
When the OCS senses that the front passen-
ger seat occupant is classified as being up
to or less than the weight of a typical
12-month-old child in a standard child re-
straint, the 75 indicator lamp
will illuminate when the engine is started
and remain illuminated, indicating that the
front passenger front air bag is deactivated.
When the OCS senses that the front passen-
ger seat is classified as being empty, the
75 indicator lamp will illumi-
nate when the engine is started and remain
illuminated, indicating that the front passen-
ger front air bag is deactivated.

115 Controls in detail
Locking and unlocking
Important notes on using KEYLESS-GO

You can also use the SmartKey with
KEYLESS-GO like a normal SmartKey
(page 110).


You can combine KEYLESS-GO func-
tions with normal SmartKey functions
(e.g. unlocking with KEYLESS-GO and
locking with button ‹).


Always carry the SmartKey with
KEYLESS-GO with you.


Never store the SmartKey with
KEYLESS-GO together with:

Electronic items such as a cellular
phone or another SmartKey with
KEYLESS-GO


Metallic objects such as coins or
metal foil
Doing so could impair the function of
the KEYLESS-GO system.


To lock or unlock the vehicle, the
SmartKey with KEYLESS-GO must be
located outside the vehicle within ap-
proximately 3 ft (1 m) of a door or the
trunk lid.


In order to start the engine with the
SmartKey with KEYLESS-GO:

The SmartKey with KEYLESS-GO
must be located in the vehicle.


The brake pedal must be firmly de-
pressed. Do not depress the accel-
erator.


If the SmartKey with KEYLESS-GO is
positioned farther away from the vehi-
cle, the system may no longer recog-
nize the SmartKey with KEYLESS-GO.
The vehicle cannot be locked or the
engine started via the KEYLESS-GO
system.


If the SmartKey with KEYLESS-GO is re-
moved from the vehicle (e.g. if passen-
ger exits the vehicle with the SmartKey
with KEYLESS-GO)
!
If you can no longer lock or unlock the vehi-
cle with the SmartKey with KEYLESS-GO, then
the batteries in the SmartKey are discharged,
the SmartKey with KEYLESS-GO is malfunction-
ing or the vehicle battery is drained.


Check the batteries in the SmartKey with
KEYLESS-GO and replace them if necessary
(page 441).


Use the mechanical key to unlock the driv-
er’s door (
page 436) and the trunk
(
page 437).


Use the mechanical key to lock the driver’s
door (
page 437) and the trunk
(
page 126).


Have the vehicle battery checked by an au-
thorized Mercedes-Benz Center.
If the SmartKey with KEYLESS-GO is malfunc-
tioning, contact an authorized Mercedes-Benz
Center.

197 Controls in detail
Automatic transmission
Emergency operation (Limp-Home Mode)
If vehicle acceleration becomes less re-
sponsive or sluggish or the transmission
no longer shifts, the transmission is most
likely operating in limp-home (emergency
operation) mode. In this mode only second
gear and reverse gear can be selected.
Stop the vehicle in a safe location.

Move the gear selector lever to park
positionP.

Turn off the engine.

Wait at least 10 seconds before
restarting.

Restart the engine.

Move the gear selector lever to
positionD (for second gear) or
positionR.

Have the transmission checked at an
authorized Mercedes-Benz Center as
soon as possible.

218 Controls in detailDual-zone automatic climate controlActivating
Moist air can fog up the windows. You can
dehumidify the air with the air condition-
ing.
Press button2 (
page 206) or
(
page 207) again.
The indicator lamp on the button
comes on.
The air conditioning uses the refrigerant
R134a. This refrigerant is free of CFCs
which are harmful to the ozone layer.Residual heat and ventilation
(Canada only)
With the engine switched off, it is possible
to continue to heat or ventilate the interior
for up to 30 minutes. This feature makes
use of the residual heat produced by the
engine.Activating

Switch off the ignition.

Press buttonT (
page 207).
REST
in the display4 (
page 207)
comes on.
Deactivating

Press buttonT (
page 207) again.
REST
in the display4 (
page 207)
goes out.
!
If the air conditioning cannot be turned on
again, this indicates that the air conditioning is
losing refrigerant. The compressor has turned it-
self off.
Have the air conditioning checked at the nearest
authorized Mercedes-Benz Center.
i
If you switch on the residual heat function
when temperatures are high, only the ventilation
will be switched on.
i
Regardless of the selected air volume, the
blower operates at low speed.
i
How long the system will provide heating de-
pends on


the coolant temperature


the temperature set by the operator
The blower will run at speed setting1 regardless
of the air distribution control setting.
i
The residual heat is automatically turned off:


when the ignition is switched on


after about 30 minutes


if the battery voltage drops


if the coolant temperature is too low